How To Patch A Broken Exhaust Pipe

So my Jeep started making more noise than it should. I tried ready made kits to repair the exhaust hole. They fell off after a few days. I tried a can with exhaust.

Edit Article How to Patch an Exhaust Pipe. Two Methods: Muffler Repair Tape Muffler Repair Putty Questions and Answers. Substances like salt can wear through the.

Nov 26, 2014  BMW e46 exhaust removal. How Take off exhaust on a 1999-2005 BMW e46 323 325 328 330. This is the same for all e 46 1999-2005 except m3. Please Subscribe.

The finishing.com Hotline: Serious Education plus the most fun you can have in metal finishing. Ted Mooney, Webmaster Melted rain suit on exhaust pipe, p. 2.

How to fix your car exhaust, without welding or power tools.

The Jumbo Tiger Patch Muffler or Tailpipe Repair Tape is a mechanically approved tape that you simply wrap-around your muffler or tailpipe and it permanently seals.

Expose the broken pipe. Keep the water on. Dig out squares of lawn a set them aside. Dig carefully around the pipe to determine where it is leaking.

How to Fix a Broken Exhaust Pipe. There are many reasons why your exhaust pipe will break. Rust leading to holes on a crushed exhaust pipe is one reason. Metal.

The old clunker s exhaust was blowing a bit, so I sealed it.

Then it fell off. It had rusted right through between the catalytic converter and the silencer.

You know what you re going to have to do, don t you., said Kitewife.

Fix it.

No, write an Instructable.

Some of my more recent projects are now here.

Wait for the engine to cool down so the exhaust pipe is cool enough to touch. Place your hand near the pipe to gauge how hot it is before actually touching it, or.

Apr 18, 2010  How to heat wrap your exhaust part 2. My first how to video Go Fast Energy: My Facebook https://www.facebook.com/uwishproduct.

Method 1 of 2: Muffler Repair Tape

1Edit step

Clean the area around the hole or crack in the tailpipe. This ensures a good seal around the affected area.

2Edit step

Preheat your car if it is below 70ºF or 21ºC until the metal is warm to the touch. Do not heat up the car if it is above 70ºF 21ºC.

3Edit step

Remove any paper or plastic backing from the tape on both sides.

Wrap the tape around the affected area until it is completely covered. Overlap the tape as necessary until it is about an inch 25.4mm thick.

It may be necessary to put a piece of aluminum over the hole before taping it if the area is too hot to touch.

5Edit step

Secure each end of the repair with wire or tape. Drive or idle your car for 20 minutes until the heat can fuse the tape to your tailpipe.

Method 2 of 2: Muffler Repair Putty

6Edit step

Clean the area around the hole or crack in the exhaust pipe with a wire brush. This ensures a good seal around the affected area.

7Edit step

Dampen the repair area with water. If the putty dried out in its container, add some water to it.

Administer putty with a knife. Press the putty deep into the hole and the surrounding area.

If you have a big hole, reinforce the area with wire or metal screening before adding the putty.

9Edit step

Idle your engine for 10 minutes to start the drying process. Do not drive the car for 24 hours after the repair is made.

10Edit step

Finished.

Give us 3 minutes of knowledge.

Warnings

Ensure you wrap the muffler tape and anchor it securely or the repair can fail.

Do not touch the muffler or tailpipe of a car that has been running for more than a few minutes. The parts can be very hot and cause severe burns.

Things You ll Need

Repair Tape or Putty

Wires

Aluminum can or foil optional

Water if using putty

Putty knife.